4/16/2023 0 Comments Precision x mini by spacepig![]() ![]() Both lack frills but are entirely practical, especially for the price. Overall, this workstation offers good upgrade potential for such a small body.įor peripherals, my review unit’s price included Dell’s $34 KM636 wireless keyboard and mouse setup. If the Precision 3240 Compact is configured without a dedicated graphics card, the case can also hold a 2.5-inch storage drive. The graphics card must be removed to access them. ![]() The two M.2 Type-2280 slots for SSDs are behind it, though they’re not visible. The M.2 slot for the wireless card is just visible under the graphics card in the photo below. (Again, see our desktop workstations guide for more on that.) ECC would only be beneficial for specialized scenarios. Error Correcting Code (ECC) memory is supported with certain CPU choices, including my unit’s Xeon, though the memory in my unit is non-ECC. Up to 64GB of memory can be installed via two 32GB DIMMs. Pinch the heatshield's release levers to take it off for cleaning and access to the two laptop-style DIMM slots, populated here by a pair of 16GB DDR4-2933 modules (32GB total). They are the most potent components available in the Precision 3240 Compact. The black heatshield covers the CPU, which in this unit is an 80-watt 10-core Xeon W-1290 (3.2GHz, up to 5.2GHz Turbo Boost). The 75-watt Quadro RTX 3000 is visible at the top of this photo. After you undo the thumb screw at the rear and slide the left plastic panel off to the rear, the top of the chassis and front panel slide forward as one piece to reveal an intricately tight interior. Getting inside the Precision 3240 Compact is puzzling the first time you try to crack the case. It would go in the cutout just above the Ethernet jack. To support a seventh monitor, you'll need to get the optional extra port-your choice of VGA, HDMI 2.0, DisplayPort, or USB-C (supporting DisplayPort over USB-C). My review unit connects with six via two full-size DisplayPort connectors on the chassis and four mini-DisplayPort connectors on its Quadro RTX 3000 graphics card. This little workstation can support up to seven monitors depending on its configuration-one more than the HP Z2 Mini G5 can do. Its stubby 3-inch antenna, not connected in the photos, screws in next to the Ethernet jack. The Intel AX201 card in my unit supports Wi-Fi 6 and Bluetooth 5. Networking comes from an Ethernet jack and optional wireless. Thunderbolt 3, not present on my unit, is available via an add-in card, though it requires sacrificing the dedicated graphics card. The power adapter connects at the lower left corner. The backside quartet of USB-A ports is split between version 3.2 Gen 2 ports on the bottom and version 3.2 Gen 1 (5Gbps) ports up top. The latter can be used to charge devices when the Precision 3240 Compact is turned off. The front-panel connectivity includes a headset jack, audio line-in/line-out, a USB 3.2 Gen 2 (10Gbps) Type-C port, and a USB 3.2 Gen 2 Type-A port with PowerShare. Other than the plastic front and left-side panels, the chassis is metal. The Precision 3240 Compact is visually professional, with no eye-catching features. Best Hosted Endpoint Protection and Security Software.The software overall is great, except the Curve setup, although I still rather use it than anything related to MSI. Pressing "X" will close it all up, sometimes messing up the custom settings. You also need to run X1 in the background all the time, if you tinker with the software, make sure to hit the "_" on the top right instead of "X", that way it gets minimized and just runs in the background. Easiest setup is select "Stealth", then move the lowest point to 30C and 14-15%, then check the Fan Curve Control box, and hit apply. It's also better to run the fans on a 14-15% bottom to prevent the annoyance of them turning on and off. ![]() Leaving fans on Auto is not the best solution, since if you have bad airflow and/or left your preset on "prefer maximum", your GPU on idle/desktop use will still consume over 30-40 watts, and heatsoak will be present. When you set up a custom curve, you need to do it with your mouse one by one in the default section, NOT in the VF Curve tab, then when you're done, press apply, select a preset number on the right, and press save. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |